Cedar Rapids Brewing Society

jjpeanasky wrote:I got a reply from BIY, they're able to get it. Listed price is $129.99 + tax per roll. I put in an order for a 100ft roll. I'll get a hold of everyone once it comes it.

Joel (@Schwerkraftbrauer), if anybody adjusts orders, you're first on the list to get the remainder.

Sounds good, I only have a 2 tap system and currently only have 7 feet of 3/16 ID hose vinyl and it works fine. So even if there's only 14 feet available I could do that as well.
Thanks Josh

Just got the email that the tubing came in. Everyone please confirm the lengths your want. Once that's complete we can figure out how to get your tubing to you, otherwise I'll just bring it to the March general meeting.

Edit: As a side note I'm dropping my "required length" to 30ft total. Changing the pint pour time to 8 seconds on that calculator shortened the length.

- Josh Peanasky

As long as it would not take away from Joel's request, I would take an additional 6 feet....I originally requested 24 feet....so my new total would be 30 feet.

I'll take 14 feet if available from leftover, otherwise let me know what the remainder is, probably make it work.
Thanks

I'll take the 21 feet I requested. Or, if it makes it work for someone else, I can take only 14.

Karl

Sent from my Pixel XL using Tapatalk

karl wrote:I'll take the 21 feet I requested. Or, if it makes it work for someone else, I can take only 14.

Karl

Sent from my Pixel XL using Tapatalk

daryl wrote:As long as it would not take away from Joel's request, I would take an additional 6 feet....I originally requested 24 feet....so my new total would be 30 feet.

I don't want to butt in because I know I did get in this thread too late for the buy, take care of everybody that was on the list first and just let me know what's left over Josh
Thanks

I'll stay at 24 ft, that'll give me 4 lines, which is one more than I have right now. And I will have to take time to install the fourth tap.

So, with the posted adjustments, I think we can all what we want:

Josh @ 30ft (70ft left)
Daryl @ 24ft (46ft left)
Karl @ 21ft (25ft left)
Tony @ 6ft (19ft left)

Joel, would you like 14 ft or 19 ft?

daryl wrote:I'll stay at 24 ft, that'll give me 4 lines, which is one more than I have right now. And I will have to take time to install the fourth tap.

So, with the posted adjustments, I think we can all what we want:

Josh @ 30ft (70ft left)
Daryl @ 24ft (46ft left)
Karl @ 21ft (25ft left)
Tony @ 6ft (19ft left)

Joel, would you like 14 ft or 19 ft?

I will definitely take the 14 feet, but would also take the 19 feet. I would almost say give it some time for everybody to speak up for that five remaining feet. If somebody can put it to good use let them have it if not I will take the 19ft, so there's no Oddball remaining small chunk

I can wait to the March meeting for mine. What's the final tally on a per ft basis?

After tax, came out to $1.30 per ft.

- Josh Peanasky

Joel, I can use that last 5 feet if you don’t need it.


Sent from my iPhone using Tapatalk

crcyclone87 wrote:Joel, I can use that last 5 feet if you don’t need it.


Sent from my iPhone using Tapatalk

I think that'll work Cal

Okay, so here's what I have:

Josh @ 30ft (70ft left)
Daryl @ 24ft (46ft left)
Karl @ 21ft (25ft left)
Tony @ 6ft (19ft left)
Joel @ 14 ft (5 ft left)
Cal @ 5ft

So this is exactly 100 ft, so hopefully I can measure okay, haha. With the cost at $1.30 per ft, here's the price breakdown:

Daryl: $31.20
Karl: $27.30
Tony: $7.8
Joel: $18.20
Cal: $6.50

I'll bring your lengths to the club meeting unless we make other arrangements. Cash please, but check works too.

- Josh Peanasky

Bump,

Anyone interested in splitting a 100' roll again this

I can start checking prices through biy, ect. if i get some more people interested.

EDIT, I'd be in for 26 feet

I would take 18 ft


Sent from my iPhone using Tapatalk